manualshive.com logo in svg

GE Profile PFCF1RKZ, Technical Service Manual

Share
Download
GE Profile PFCF1RKZ Technical Service Manual Download Page 63

– 63 –

Heater Troubleshooting

AC Heaters

Resistance 

Air Duct Heater ***

578 

Defrost Heater * (See 

Defrost Heater

.)

31 

Double Drawer Mullion Heater * (See 

Double Drawer Mullion Assembly

.)

827 

Duct Port Heater ***

1200 

Freezer/Fresh Food Mullion Heater *** (See 

Fresh Food/Freezer Mullion Heater

.)

1653 

Return Duct Heater LH *** (See 

Return Duct Heaters

.)

440 

Return Duct Heater RH *** (See 

Return Duct Heaters

.)

440 

Supply Duct Heater ***

1653 

* Replaceable individual heater

** Replaced as door assembly

*** Not replaceable

Note:

 

•  Air Duct and Supply Duct heaters will come on with abnormally high door open time and high humidity. 

(Abnormal = approximately 70 fresh food door openings for 12 seconds or more in a 16 hour period.)

•  Duct Door heater, Door Gasket heater, and Recess heater are on 100% of the time when the freezer set 

temperature is 4°F or lower. Above 4°F heater on-time will vary. 

•  Duct Port heater is located around ice compartment port holes, and cycles on temperatures and ice 

compartment conditions. (Mid-settings = heater on time approximately 30%)

•  Fill Tube heater will be on after water valve activation or when ice is dispensed. 

DC Heaters

Resistance (Approximate)

Door Gasket Heater **

62 

Duct Door Heater * (See 

Dispenser and Interface

.)

109 

Fill Tube Heater **

300 

French Door Vertical Mullion Heater * (See 

Articulating

 

Door Mullion

.)

24 

Recess Heater **

145 

Summary of Contents for Profile PFCF1RKZ



































































Reviews:

No comments

Brands by name

Popular brands

Load more brands