manualshive.com logo in svg

GE Profile PFCF1RKZ, Technical Service Manual

Share
Download
GE Profile PFCF1RKZ Technical Service Manual Download Page 35

– 35 –

Auger Motor

The auger utilizes a 120 VAC motor rated at 10.2 
watts and draws .09 amps. The rated speed is 24.5 
rpm. As viewed with the ice bucket out, clockwise 
rotation of the auger motor provides crushed ice, 
counterclockwise rotation produces cubes.

To remove the auger motor:

1.  Remove the icemaker. (See 

Icemaker

.)

2.  Remove the 1/4-in. hex-head screw and the 

wiring access cover from the auger motor 
housing.

3.  Disconnect the ice compartment wire harness.

4.  Remove the three 1/4-in. hex-head screws from 

the auger motor housing.

5.  Pull out the auger motor housing from the ice 

compartment.

Cover

Disconnect

Auger Motor Housing

6.  Disconnect the auger motor wire harness.

7.  Disconnect the 2 ground wires from the metal 

rear cover.

8.  Remove the tape from the metal rear cover 

located at the back of the housing.

9.  Using a small 

fl

 at blade screwdriver, uncrimp the 

metal tabs located at the top right and bottom 
left corners of the metal rear cover. Remove the 
cover.

Disconnect

Tape

Tape

Tab

Disconnect

Disconnect

(

Continued next page

)

Summary of Contents for Profile PFCF1RKZ



































































Reviews:

No comments

Brands by name

Popular brands

Load more brands