GE Profile PFCF1RKZ Technical Service Manual Download Page 37 | Manualshive

Page: 37 / 66

– 37 –

2. Carefully lower the interface and disconnect the

3 wire harnesses.

3. Remove the 4 Phillips-head screws and the

dispenser housing from the dispenser recess.

Wire Harnesses

The dispenser cradle switch is attached to the left
side of the dispenser housing with a Phillips-head
screw.

Each of the 2 dispenser LED boards are attached to
the dispenser housing with a plastic clinch rivet.

Switch

Rivet

LED Board

The duct door heater consists of the heater, door,
and door seal, available as an assembly. The heater
operates on 13.6 VDC and has an approximate
resistance value of 109



. The assembly is

connected with a single wire harness and can be
unsnapped from the solenoid-operated door crank.

The duct door heater is in a parallel circuit with the
recess heater and the door gasket heater. These
heaters operate based on temperature settings.

For

example, a freezer setting of mid-range temperature
or higher equals 100 percent on-time except during
ice dispense. Applied voltage to this circuit can be
tested at dispenser board J4-2 to J4-6.

The solenoid operates on 13.6 VDC and has an
approximate resistance value of 13



. The solenoid

is connected with a single wire harness and is
attached to the recess with 3 Phillips-head screws.
Applied voltage to solenoid can be tested at
dispenser board J1-1 to J1-2.

Door Crank

Solenoid

Duct Door Heater

13.6 V RED

J4-2

DISPENSER BOARD

J4-6

J1-1

J1-2

BL

AC

K

BL

AC

K

DUCT DOOR HEATER

DOOR GASKET HEATER

RECESS HEATER

R=109

R=62

R=145

RED

RED

RED

WHITE

DUCT DOOR SOLENOID

(

Continued next page

)

«
...
35
36
37
38
39
...
»

Summary of Contents for Profile PFCF1RKZ



































































Reviews:

No comments

Related manuals for Profile PFCF1RKZ

Brand: Jenn-Air Pages: 36

Brand: Jenn-Air Pages: 40

Brand: Jenn-Air Pages: 53

Brand: Jenn-Air Pages: 60

Brand: Oceanic Pages: 118

Brand: GE Pages: 136

Brand: Union Pages: 36

Brand: eta Pages: 100

Brand: Premium Pages: 11

Brand: Summit Pages: 12

Brand: DAKO Pages: 37

Brand: Saivod Pages: 36

Brand: Fagor Pages: 76

Brand: Smeg Pages: 26

Brand: Beko Pages: 68

Brand: Beko Pages: 32

Brand: Beko Pages: 32

Brand: Beko Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands