manualshive.com logo in svg

GE PanaFlow HT, User Manual

Share
Download
GE PanaFlow HT User Manual Download Page 51

PanaFlow HT User’s Manual

41

Chapter 3. Initial Setup and Programming

3.6.1 Settings

 To check and/or change the desired settings, under 

User Preference

, select 

Settings

 and press 

[

]

.

 The following screen appears.

To change the language being used, highlight 

Language

 and press 

[

]

.

 ‘The 

following screen appears.

Use the [

] or [

] arrow keys to select the desired language and press 

[

]

 twice. 

(Only English is currently available.) The screen returns to the previous display.

To check the 

Meter Tag

 and/or 

Label

, highlight your choice on the 

UserPref/Setting

 menu and press 

[

]

. Press [

]

 to return to the previous screen.

Note: 

You can only change the Meter Tag and Label data using Vitality software.

To check and/or change the date/time, highlight 

System Date

 and press 

[

]

. The 

following screen appears.

System Date

System Date

System Date

System Date

Summary of Contents for PanaFlow HT




































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands