manualshive.com logo in svg

GE PanaFlow HT, User Manual

Share
Download
GE PanaFlow HT User Manual Download Page 146

PanaFlow HT User’s Manual

137

Appendix E. Special Applications

E.2  Path Error Handling (cont.)

3-path system (with 2-path error handling ON):

Note:

Path 1 and Path 2 are the mid-radius paths. Path 3 is the diameter path. There is no symmetrical path for Path 
3.

With 2-path Error Handling set to OFF, there are only two error conditions. If any one path is in error, the reaction is 
Single Channel Error, stop measuring. If more than one path is in error, the reaction is Multichannel Error, stop 
measuring.

 

Error Detection Scenario

Action

Path 1 error

Substitute path 2 measurement, keep 
measuring

Path 2 error

Substitute path 1 measurement, keep 
measuring

Path 3 error

Single Channel Error, stop measuring

Path 1 and Path 2 in error

Multichannel Error, stop measuring

Path 2 and Path 3 in error

Multichannel Error, stop measuring

Path 1 and Path 3 in error

Multichannel Error, stop measuring

Path 1, Path 2, and Path 3 in error

Multichannel Error, stop measuring

Summary of Contents for PanaFlow HT




































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands