manualshive.com logo in svg

GE Monogram ZBD3500, Installation Instructions Manual, Page: 28 / 32

Share
Download
GE Monogram ZBD3500 Installation Instructions Manual Download Page 28

28

GPF475 Trim Kit

3/4" Custom Panels

• Drill 3 holes 3/16" dia. into the access panel

as shown.

• Place the custom panel onto the access

assembly and mark hole locations.

• Drill 3 holes, 1/8" dia. holes, 5/8" deep into

the custom panel.

• Align the custom panel with screw holes and

drive 3 screws into the back side of the
assembly panel and through the custom
panel. The top edges should align evenly.

Caution: 

Do not drill pilot holes too deeply to avoid damaging

the appearance side of the panel.

Step 5
Install Custom
Panel To
Access Assembly

Step 6
Install Access
Panel Assembly
And Toekick

• Place the toekick against the bottom of the

dishwasher.

• Place the access panel assembly against the

dishwasher and tighten the attached screws.

• Re-install two original bottom screws loosely.

Adjust the toekick up or down and tighten
screws.

1/2" to 2"

3/16" Dia.
Three Places

1/2" to 2"

1/2" to 2"

Center Line

1/2" to 2"

Tighten 2 Screws

Summary of Contents for Monogram ZBD3500

































Reviews:

No comments