manualshive.com logo in svg

GE Monogram ZBD3500, Installation Instructions Manual, Page: 21 / 32

Share
Download
GE Monogram ZBD3500 Installation Instructions Manual Download Page 21

21

GPF400S Trim Kit

Stainless Steel Door and Access Panels

• Remove protective plastic film.
• Tip door panel and slide up and under

bottom and sides of escutcheon.

• Snap door panel over the door and slide

upwards, under the escutcheon.

• Remove protective plastic film.
• Locate and install 2 original screws and

retainers into the top holes of the stainless
access panel.

• Place the stainless access cover on the access

panel assembly.

• Drive 3 screws through the bottom of

stainless cover.

• Center punch and drill one hole into each

side of the stainless cover.

• Install screws supplied.

• Place the toekick against the bottom of the

dishwasher.

• Place the access panel assembly against the

dishwasher and tighten the attached screws.

• Re-install two original bottom screws loosely.

Adjust the toekick up or down and tighten
screws.

Step 2:
Install Stainless
Door Panel Cover

Step 3:
Install GPF100
Spring Kit

Step 4:
Install Stainless
Access Panel
Onto Access
Panel Assembly

• Drive 3 screws into the bottom of the panel

using a phillips head screwdriver.

• Center punch and drill holes through the

holes in the stainless panel and into the
dishwasher door, 2 on each side.

• Install screws supplied.

This kit must be installed to achieve proper
door balance which is affected by the addition
of this stainless door panel.
• Follow the instructions provided with the

GPF100 kit.

Step 5:
Install Access
Panel Assembly

New 

Door Panel

Cover

Cover

Retainers

Tighten 2 Screws

Summary of Contents for Monogram ZBD3500

































Reviews:

No comments