manualshive.com logo in svg

GE Monogram ZBD3500, Installation Instructions Manual, Page: 20 / 32

Share
Download
GE Monogram ZBD3500 Installation Instructions Manual Download Page 20

20

GPF400S Trim Kit

Stainless Steel Door and Access Panels

CAUTION

WARNING

To prevent electric shock, discon-
nect electrical power supply to
dishwasher before changing
panels. Do not operate dishwasher
while changing panels or when

lower access panel assembly is removed.

T

ools and Materials required:

• 1/4" socket driver

• Phillips screwdriver

• Electric drill

• 1/8" drill bit

• Safety glasses

• Center punch

• Gloves to protect against sharp edges

• Remove the two screws below the access panel.

Retain screws.

• Loosen the two screws located between the door and

the access panel.

• Remove the access panel assembly from the dish-

washer.

• Remove plastic screw retainers holding the screws to

the access panel. Save screws and retainers.

• Remove the toekick and set aside.
NOTE: Do not remove the insulation behind the
access panel or toekick.

The GPF400S Stainless steel trim kit covers
the existing door and access panel.

This kit includes:
• Door and access panel covers.
• 12 screws.
• GPF100 Spring kit

To Clean These Stainless Steel Panels:
Stainless steel has some unique cleaning
characteristics. In order to keep your
dishwasher looking like new we suggest
cleaning it with Stainless Steel Magic or a
similar product.

Stainless Steel Magic is available at Ace, True
Value, Servistar, HWI and other leading
stores. It is also available through GE Parts
by calling 1-800-626-2002 and ordering part
number WX10X15.

Step 1

Loosen 2 Screws

Escutcheon

Door

Panel

Access Panel

Toekick

Loosen 2 Screws

Escutcheon

Door

Panel

Access Panel

Toekick

Summary of Contents for Monogram ZBD3500

































Reviews:

No comments