manualshive.com logo in svg

GE Monogram ZBD3500, Installation Instructions Manual, Page: 14 / 32

Share
Download
GE Monogram ZBD3500 Installation Instructions Manual Download Page 14

14

Installation

CleanSensor Dishwasher

Step 10
Slide Dishwasher
Into Cabinet

DO NOT PUSH AGAINST
FRONT DOOR PANEL
WITH KNEES. Damage to
the door panel will occur.

• Level the dishwasher by adjusting the four

leveling legs individually for correct align-
ment.

• Dishwasher should be level, left to right and

front to back for best performance.

• Route the water and electrical supply within

reach of their connection locations under
the dishwasher. Avoid contact with springs
or other components.

Step 11
Level Dishwasher,
Align
Connections

• Slide dishwasher into the opening a few

inches a time. As you proceed, pull the drain
hose through the opening and under the
sink.

• Make sure drain hose is not kinked under

the dishwasher.

• Check to be sure there is no interference

with water line and wiring.

• Open the door and position the dishwasher

tub flange 3/4" from the cabinet opening.

• Fasten the dishwasher to the underside of

the countertop, using the 2 Phillips screws
provided. Be sure screws are driven straight
and flush to avoid interference with door
operation.

Important: 

The dishwasher must be centered in the opening and

have no interference when opening or closing the door.

Interference may cause a water leak or make noise when opening

and closing the door.

Step 12
Position
dishwasher
and fasten
to cabinet

• Connect water supply line to 90

°

 elbow

previously installed.

• Open and close the door to insure that door

springs do not come in contact with water
line.

Step 13
Connect
water supply

CAUTION

Rear View

Water

Electric

3/4"

90

°

 Elbow

Hot Water

Supply

Door Spring

Fill Hose

Summary of Contents for Monogram ZBD3500

































Reviews:

No comments