manualshive.com logo in svg

GE Monogram ZBD3500, Installation Instructions Manual, Page: 22 / 32

Share
Download
GE Monogram ZBD3500 Installation Instructions Manual Download Page 22

22

GPF425 Series Trim Kit

1/4" Custom Panels

Step 1:
Cut 1/4"
Thick Custom
Panel To Size

Step 2:
Remove Lower
Access Panel
Assembly

GPF425B, Black Trim Kit
GPF425W, White Trim Kit
GPF425A, Almond Trim Kit

CAUTION

WARNING

To prevent electric shock, discon-
nect electrical power supply to
dishwasher before changing
panels. Do not operate dishwasher
while changing panels or when

lower access panel assembly is removed.

T

ools and Materials required:

• 1/4" socket driver

• Phillips screwdriver

• Electric drill

• 1/8" drill bit

• Masking tape

• Safety glasses

• Gloves to protect against sharp edges

• Cut door panel and access panel to the

dimensions shown.

NOTE: The trim provided will conceal the cut
edges of the panels.

The GPF425 trim kits provide for the installa-
tion of 1/4" thick custom door and access
panels.
This kit includes:
• Left, right and bottom door trim
• Top and bottom access panel trim
• Color matched screws

• Remove the two screws below the access

panel. Retain screws.

• Loosen the two screws located between the

door and the access panel. Do not attempt
to remove these screws. They are secured to
the access panel with washers.

• Remove the access panel assembly from the

dishwasher.

• Remove the toekick and set aside.

NOTE: Do not remove the insulation behind
the access panel or toekick.

1/4" Thick

Door Panel

23-9/16"

3-11/16"

19-3/4"

1/4" Thick Access Panel

Loosen 2 Screws

Escutcheon

Door

Panel

Access Panel

Toekick

Loosen 2 Screws

Escutcheon

Door

Panel

Access Panel

Toekick

Summary of Contents for Monogram ZBD3500

































Reviews:

No comments