manualshive.com logo in svg

GE Monogram ZBD3500, Installation Instructions Manual, Page: 19 / 32

Share
Download
GE Monogram ZBD3500 Installation Instructions Manual Download Page 19

19

GPF400/600/700 Series Trim Kits

Door and Access Panel Change

Step 2:
Install New
Door Panel Cover

Step 3:
Install New
Access Panel
Assembly And
Toekick

• Remove protective plastic film.
• Place the toekick against the bottom of the

dishwasher.

• Place the new access panel assembly against

the dishwasher and tighten the attached
screws. (GPF600, re-install original access
panel.)

• Re-install two original bottom screws loosely.

Adjust the toekick up or down and tighten
screws.

Note: 

The new door panel cover will completely cover the

existing door. Do not remove the original door panel.

For GPF400 and GPF600 Kits:
• Remove protective plastic film.
• Tip door panel and slide up and under

bottom and sides of escutcheon.

• Snap door panel over the door and slide

upwards, under the escutcheon.

• Drive 2 screws into the bottom of the panel

using a phillips head screwdriver.

New 

Door Panel

Cover

Tighten 2 Screws

Summary of Contents for Monogram ZBD3500

































Reviews:

No comments