background image

 

GFK-3000A 

IC695ACC403 Quick Start Guide 

Ordering Information 

IC695ACC403 

Energy Pack.

 

Includes base, 

CapPack module and Energy Pack 
to Controller cable.

 

IC695ACC413 

Replacement CapPack module. 

IC695CBL003 

Replacement 0.6m (24

) Energy 

Pack to Controller cable. 

2

 

Hardware Installation 

The Energy Pack can be mounted on a standard EN50022 
DIN rail or an equipment panel. It is designed to be 
mounted adjacent to the Controller and connected to the 
Controller using the provided cable (IC695CBL003). 

  

Heat dissipation:

 When mounting the Energy Pack, 

allow a minimum clearance of 25.4mm (1 inch) on all four 
sides of the unit (right, left, top and the bottom). 

2.1

 

Mounting the Energy Pack on a DIN Rail 

The Energy Pack snaps easily onto the DIN rail. No tools 
are required. 

1)

 

Incline Energy Pack so that top edge of plastic 
recess (Figure 2) engages top of DIN rail 

2)

 

Swivel the Energy Pack so that bottom spring-
loaded plastic clip engages bottom of DIN rail. 

3)

 

Listen for click as plastic clip springs back, 
securing the Energy Pack onto the DIN rail. 

Summary of Contents for GFK-3000A


















Reviews: