GE DuraStation Operation And Maintenance Download Page 30

Page: 30 / 36

DuraStation™ EV Charger User Manual

GE Industrial Solutions

Kits

6.1

Pedestal Assembly Catalog Numbers

Description

Connect

Communication

Catalog No.

Single Pedestal w/ Connect

Yes

CAT 5

EVDPR3GEXXGB

Single Pedestal w/ Connect

Yes

WiFi

EVDPR3GWXXGB

Single Pedestal w/ Connect

Yes

Cellular (CDMA)

EVDPR3GZXXGB

Single Pedestal w/ Connect

Yes

Cellular (GSM)

EVDPR3GAXXGB

Double Pedestal w/ Connect

Yes

CAT 5

EVDDR3GEXXGB

Double Pedestal w/ Connect

Yes

WiFi

EVDDR3GWXXGB

Double Pedestal w/ Connect

Yes

Cellular (CDMA)

EVDDR3GZXXGB

Double Pedestal w/ Connect

Yes

Cellular (GSM)

EVDDR3GAXXGB

Table – 5.1

6.2

Replacement kits

The EV Charging Station offers the following replacement kits, Refer the respective Instruction
sheets from the package for the installation of these kits.

Catalog #

Description

EVWSKEY01

Service access door keys - Qty 2 Nos

EVRCG10

RFID Card – Pack of Qty 10 Nos

EVRP01

RFID Enrollment reader CM5321CL USB – 13.45MHz

EVWTFUSE01

Replacement Fuses

EVWSCR01

Contactor Replacement Kit

EVDSRR01

RFID Replacement

EVDSLED01

LED Replacement - EVSE Single Pedestal

EVDSLED02

LED Replacement – EVSE Wall/Pole

EVDSLED03

LED Replacement – EVSE Double Pedestal

EVDSVFD01

VFD Replacement Kit

EVDSDR01

Service Door Replacement Kit – Wall/Pole

EVDSDR01

Service Door Replacement Kit – Single/Double Pedestal

EVDSCBL01-20

Charging Cord Replacement Kit – Single Pedestal

EVDSCBL02-20

Charging Cord Replacement Kit – Wall/Pole

EVDSCBL03-20

Charging Cord Replacement Kit – Double Pedestal

Table – 5.2

Summary of Contents for DuraStation





































Search results

Summary of Contents for DuraStation

Reviews:

Related manuals for DuraStation

Brands by name

Popular brands

GE DuraStation, Operation And Maintenance

Search results

Summary of Contents for DuraStation

Reviews:

Related manuals for DuraStation

Brands by name

Popular brands