background image

Installation Preparation

7

Preparation 

WITHOUT

 an Accessory Storage Drawer

PREPARE THE OPENING 

(CONT.)

Installation over a GE/Monogram Oven and 

Warming Drawer:

NOTE:

 Additional clearances between the cutouts 

may be required. Check to be sure the oven 

supports above the Warming Drawer location do 

not obstruct the required interior depth and height. 

See Warming Drawer installation instructions for 

details.

 CAUTION:

 

For personal safety, the 

mounting surface must be capable of supporting 

the cabinet load, in addition to the added weight 

of this approximate 80-pound oven, plus additional 

oven loads of up to 50 pounds or a total weight  

of 130 pounds.

PRECAUCIÓN:

 Para seguridad 

personal, la superficie de montaje debe poder 

soportar la carga del gabinete, además del peso 

aproximado de 80 libras del horno, más las 

cargas adicionales del horno de hasta 50 libras  

o un peso total de hasta 130 libras.

Construct 

Solid Bottom 

Min. 3/8” 

Plywood 

Supported by  

2x4 or 2x2 

Runners all  

Four Sides

30”

23-1/2”

25-1/4”

17-1/2”

2” Min.

Per Oven 

Requirement

45-1/4” 

Min.

Per warming drawer requirement

2” Min.  
(3” recommended)

PREPARE THE OPENING 

(CONT.)

Installation over a GE/Monogram Oven:

‡,I\RXDUHUHSODFLQJD*(0RQRJUDPHOHFWULF

double oven with the combined installation of  

an Advantium 240V and a single oven, use the 

dimensions shown. The middle rail separating  

the two openings may need to be larger than  

the 2” minimum shown.

30”

23-1/2”

25-1/4”

17-1/2”

2” Min.  
(3” recommended)

45-1/4”

Min.

Construct Solid 

Bottom Min. 

3/8” Plywood 

Supported by  

2x4 or 2x2 

Runners all  

Four Sides

Per Oven 

Requirement

Summary of Contents for Advantium ZSC2201JSS

















Reviews: