background image

Design Information

4

PRODUCT DIMENSIONS AND CLEARANCES   

NOTE:

 Appearance will vary by model.

TOOLS AND PARTS REQUIRED  

(NOT SUPPLIED

)

‡

 #2 Phillips screwdriver

‡

 Hand held drill

‡

 High speed drill bit, 3/32" diameter

‡

 3/8" slot head screwdriver

‡

 Level

‡

 Saw

‡

  2x4 or 2x2 lumber for installing runners  

or 3/8" plywood for floor (if required)

‡

  Wood screws or other hardware for installing 

runner or shelf to support oven (if required)

‡

 Safety glasses or goggles

PARTS SUPPLIED 

‡

 6 brass screws (3 required, 3 extra)

‡

 5 color matched screws (4 required, 1 extra)

‡

 Bottom trim

ELECTRICAL TOOLS AND PARTS 
REQUIRED (NOT SUPPLIED)

‡

 Junction box

‡

  Electrical cable (3-conductor or 4-conductor wire as 

required by local codes)

‡

 UL-listed conduit connectors

‡

 Wire cutters and wire strippers

ADVANCE PLANNING

‡

  These ovens may be installed directly into a 30” wide 

oven cabinet.

‡

  Cutout dimensions are NOT the same for installation 

with or without an accessory storage drawer. Make 

sure to use the correct cutout when preparing the 

opening.

   

NOTE: 

Model ZSC2202 CANNOT be installed with 

an accessory storage drawer. See Installation 

Preparation Without an Accessory Storage Drawer  

for this model.

IMPORTANT

³

 

This oven is not approved for 

use above another built-in Advantium Speedcook 

oven, a side by side installation or below a 

countertop.

‡

  For personal safety, this oven cannot be installed 

in a cabinet arrangement such as an island or 

peninsula.

‡7KHRYHQPXVWEHLQVWDOOHGDWOHDVWµDERYH

the floor.

‡$OORZIRUFOHDUDQFHWRDGMDFHQWFRUQHUVZDOOV

drawers, etc.

‡&DELQHWVLQVWDOOHGDGMDFHQWWRZDOORYHQV

must have an adhesion spec of at least 194ºF 

temperature rating.

The oven must be securely installed in a cabinet 

that is firmly attached to the house structure. 

Weight on the oven door could cause the oven  

to tip and result in injury. Never allow anyone to 

climb, sit, stand or hang on the oven door.
If installing the drawer accessory, the drawer must 

be assembled to the oven prior to installation into 

the cabinet. See the 

Accessory Storage Drawer 

Assembly Instructions

.

21-1/2”

1”

13”

19”

29-3/4”

1-1/10

s

1-3/5

s

Summary of Contents for Advantium ZSC2201JSS

















Reviews: