background image

Installation Instructions

11

2   ROUTE CONDUIT THROUGH 

CUTOUT (CONT.)

When connecting to a 3-conductor branch circuit:

‡

  Connect oven red lead to branch circuit red lead.

‡

  Connect oven black lead to branch circuit black 

lead.

‡

  Connect oven green ground lead and white lead  

to branch circuit neutral (white or gray).

When connecting to a 4-conductor branch 

circuit:

‡

  Connect oven red lead to branch circuit red lead.

‡

  Connect oven black lead to branch circuit black 

lead.

‡

  Break connection between oven white lead and 

oven green ground lead.

‡

  Connect oven white lead to branch circuit neutral 

lead (white or gray).

‡

  Connect oven green ground lead to branch circuit 

ground lead (green or bare copper).

2   ROUTE CONDUIT THROUGH CUTOUT

CAUTION:

 

Two people are required to 

lift the oven into the opening. Grasp the bottom 

at front and rear. Discard foam base. DO NOT USE 

HANDLE OR CONDUIT TO LIFT THE OVEN. DAMAGE 

WILL OCCUR.

PRECAUCIÓN:

 

Se requiere contar con 

dos personas para colocar el horno en la abertura. Se 

deberá tomar la parte inferior sobre la parte frontal 

y trasera. Descarte la base de gomaespuma. NO USE 

LA MANIJA NI LOS CONDUCTOS PARA LEVANTAR EL 

HORNO. SE PRODUCIRÁN DAÑOS.
With oven in front of the cabinet opening:

‡

  Insert conduit into cabinet opening. Connect oven 

wiring and branch circuit.

‡

  Lift the oven into the opening while continuing to 

feed the conduit in the direction of the installed 

junction box. Be sure the conduit does not get 

pinched between the back of the oven and the 

cabinet wall.

‡

  Leave oven a few inches forward of the cabinet 

front frame. Do not push the unit all of the way 

into the cutout.

WARNING

 

‡

  Disconnect power to the junction box before 

making the electrical connection.

‡

  Electrical ground is required on this appliance. 

‡

  Do not connect the electrical supply until 

appliance is permanently grounded.

ADVERTENCIA

 

‡

  Desconecte la corriente de la caja de empalmes 

antes de realizar la conexión eléctrica.

‡

  Este electrodoméstico requiere que se realice una 

conexión a tierra.

‡

  No conecte al suministro de corriente hasta que 

el electrodoméstico se haya conectado a tierra 

de forma permanente.

(Oven shown without 

accessory storage drawer.)

GROUNDING INSTRUCTIONS

This appliance must be connected to a grounded, 

metallic, permanent wiring system, or an equipment 

grounding connector should be run with the circuit 

conductors and connected to the equipment 

grounding terminal or lead on the appliance.
Failure to follow these instructions could result  

in fire, personal injury or electrical shock.

Summary of Contents for Advantium ZSC2201JSS

















Reviews: