background image

2

Both one and two-car doors are installed in 
the same manner.
Be sure all warning labels and tags are 
properly affixed to the door and that the home 
owner information is left with the purchaser.

GENERAL NOTES

WHO SHOULD  

INSTALL THIS DOOR?

A minimum of two people must be 
available for fitting. However due to the 
weight and spring tension of larger doors, 
we insist that three people or suitable 
lifting gear be available for installation

 on 

doors over 10ft wide or 9ft high. 

PRE-INSTALLATION CARE AND HANDLING

•  The door curtain must be handled with care at 

all times

•  The doors length must be supported in its 

entirety during transport and handling

•  The door must be stored on a flat 

DRY

 surface

•  Packaging must not be removed until 

instructed (at the correct step in the 

installation)

Ensure that the area around the opening is 
strong enough to support the door.

!

!

!

!

WARNING! 

FRAGILE!

WARNING!

KEYPOINTS: ELECTRICALLY 

OPERATED DOORS

Please read the instructions relating to the 
installation of an electric motor prior to 
commencing. Key guidance is summarised 
here and repeated at the relevant step in the 
installation.
• The installed door must operate efficiently when 

used manually. Ensure sufficient clearance 
between door and bracket to facilitate fitting of 
motor (See Side Clearance, page 4). 

•  Turn off the power before making any 

adjustments. 

•  Make sure the anti-coning collar is adjusted 

and secure on the drum shaft to eliminate 
sideways movement on the opposite side to 
which motor is to be fitted. 

• When installing the door, ensure the motor is 

disengaged and the drum turns freely. 

• Never engage the manual release with motor 

running. 

• The upper limit on the operator should be set 

to stop the roller door, 30-40mm below the 
guide stop, to avoid damaging the drive gears. 

• Weight bar must be attached to bottom bar 

with rivets/bolts. 

This new GDS door has been designed for ease of operation, security and attractive 

appearance with minimal maintenance. Performance of the door will be impaired if it 

is installed incorrectly. 

Read these instructions carefully before commencing the 

installation. Warranty is void if the door is not installed correctly according to 

these instructions.

!

!

Goggles
Safety Shoes
Gloves

SAFETY EQUIPMENT

www.samsondoors.co.uk

0800 328 6250

www.samsondoors.co.uk

www.samsondoors.co.uk

0800 328 6250

www.samsondoors.co.uk

Summary of Contents for DuraRoll





















Reviews: