17
18
The InductWarm
®
200 has a dish detection. This ensures that the induction field is only active when placing an
inductive dish on top. When the InductWarm
®
200 is operating with a dish, the small LEDs are shining. If the dish
will be removed, the InductWarm
®
200 system recognizes the situation and turns off automatically. This is being
indicated by four blinking LEDs. If the dish will be replaced within five minutes the system starts warming on the
same level as before, after that the systems will switch to standby mode. The InductWarm
®
200 can be used wih any
induction capable dishes.
You can use the touch panel or remote control to operate each individual warming zone separately. This allows you a
very high level of variety in the combination of meals that can be presented. By pressing one of the overall tempera-
ture buttons you can change the temperature level of all zones combined.
Cleaning and Care
Glass ceramic
We recommend using dishes with flat bases to avoid any potential surface damage such as scratches. However, if si
-
gns of use like this do appear on your warming surface, it will not impair the warming process in any way.
Cleaning tips:
•
First, use a scraper to remove all large pieces of dirt and food leftovers from the warming surface.
•
Then squeeze a few drops of a suitable cleaning product on to the cold surface and rub it in with kitchen paper or
a clean cloth.
•
Then wipe down the warming surface with water and rub it dry with a clean cloth.
•
Clean your warming surface regularly, preferably after each use.
Daily Cleaning
For cleaning: Switch off the InductWarm
®
200 Tabletop appliance. Wait until the InductWarm
®
200 appliance has
cooled to hand temperature before starting to clean.
Please note: Do not use steel wool or sharp objects. Your induction warming appliance is not splash-water resistant.
Therefore, do not use running water or steam to clean it. To remove dirt and deposits on side walls, you can use
standard pH-neutral cleaning products based on non-ionic and anionic tensides and mild organic solvents such as
alcohol and glycols. Finally, remove all cleaning product residue, wipe down the cleaned surfaces with water, and rub
dry with a dry cloth.
Important: If any plastic objects, aluminium foil, sugar or food containing sugar accidentally melt on to the
hot warming surface, wipe them off the hot warming zone immediately with a cleaning scraper to prevent
surface damage. Never use scouring sponges or scouring products. Chemically aggressive cleaners such as
oven spray and stain remover are also unsuitable.
Troubleshooting
Possible problems
Fault
Cause
Remedy
No heat, LED is not blinking
No power supply
Plug the appliance in,
check the plug connection
Power line fuse tripped
Check and reset the fuse
Appliance not switched on
Switch on appliance with the on /
off switch
Appliance defect
Contact customer service
LED flashing
Pan is not detected
Pan too small or not
induction compatible
Dish is not warm enough
Incorrect placement of dish
Ensure right position above the
induction coil
Too little energy input
Increase power level
Dish is not induction compatible
Check induction compatibility of
dish
Safety Regulations
Responsibility
The InductWarm
®
130 reflects the state of the art and has been built in accordance with the valid CE guidelines. Safe
operation is assured. The InductWarm
®
130 appliance is not intended to be operated by children or persons with phy-
sical or mental limitations, unless they are instructed and monitored while using the appliance by a person respon-
sible for their safety.
Gastros Switzerland AG disclaims all liability in cases due to unauthorised conversions or modifications by the custo
-
mer. If the mains supply cable for the appliance is damaged, it must be replaced by the manufacturer, an authori-
sed service agent or other similarly qualified person in order to prevent hazards. The connection for the mains plug
should always be positioned so that it is freely accessible. If this is not possible, a master switch for the appliance
must be installed by the customer. In the event of a malfunction, the appliance must be switched off completely by
unplugging the mains plug or by turning off the master switch.
When transporting, setting up, maintaining and repairing the InductWarm
®
130 appliance, the latest version of the
following regulations and guidelines that are applicable in your country must be observed:
•
Regulations of professional electricians‘ associations, e.g. VDE, SEV, etc.
•
EC directives (in EU countries)
•
Accident prevention regulations