GAS Gasmaster Installation, Operation And Maintenance Manual Download Page 39

Page: 39 / 45

4.3 Detector Calibration

Gas Alarm Systems recommends that you check

detectors routinely to ensure correct calibration and

operation.
Gas detectors require recalibration at least every 3 to 6

months. Fire detectors should be tested with the same

frequency. Site procedures may require more frequent

testing. See section 2.12 on page 14 for calibration

instructions.
For detailed instructions on the routine functional

testing of detectors, please refer to the relevant

Installation, Operating and Maintenance Instructions

provided with each detector.

4.4 Changing Batteries

During routine servicing, it is recommended that the

power be isolated from Gasmaster temporarily to

ensure that the back-up batteries are operational. Gas

Alarm Systems recommend that batteries are changed

every two years, and replaced as a pair.
Replacement batteries should be Yuasa UCEL Y1.2-12,

12 v 1.2 Ah C20 lead-acid type cells.
A 10 A fuse is fitted to the batteries, for replacement

part number see Spare Parts and Accessories section.

Batteries should be checked regularly on units

operating over 40ºC.

Warning
When replacing batteries, care should be taken to

ensure cables are re-fitted as shown on the battery

connection diagram. Incorrect fitment of battery

cables may result in a fire and/or harm to personnel.

4.5 Module Replacement

In the unlikely event of a Gasmaster component failure,

Gas Alarm Systems recommend that repair should

not be undertaken by anyone other than Gas Alarm

Systems approved personnel. Please contact Gas Alarm

Systems for details of your nearest service centre.

4.6 Event logging

Gasmaster records alarms, faults and display panel

button activities in an Event Log. A maximum of 300

events are logged, after which data is over-written on

a first-in-first-out basis. This function provides a record

of all system activities which can be uploaded using

Gasmaster PC software at any time. The event log is

held in RAM (volatile memory), so in the event of a

complete power failure all data will be lost.

4.7 Service card

A card is fitted to the inside of the front cover for

logging service activity. It is recommended that this

card be filled in with the dates of services, and details

of any parts replaced.

4.8 Cleaning

If required, the outside of the Gasmaster case can be

cleaned by gently wiping with a damp cloth using a

mild soap solution only.

4. Maintenance

Summary of Contents for Gasmaster














































Search results

Summary of Contents for Gasmaster

Reviews:

Related manuals for Gasmaster

Brands by name

Popular brands

GAS Gasmaster, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for Gasmaster

Reviews:

Related manuals for Gasmaster

Brands by name

Popular brands