GAS Gasmaster Installation, Operation And Maintenance Manual Download Page 42

Page: 42 / 45

Part No.

Description

Comment

E01875 12V

1.2Ah battery

2 required

E07534

Battery fuse assembly

Assembly with fuse, fuse holder and loom

M05897

Service card

Replacement service cards, minimum quantity 10

M07624

Installation, Operation and

maintenance manual

S012016

Display PCB

For all Gasmaster models

S013047

Gasmaster 4 terminal PCB

No links supplied, use links from old PCB

S013046

Gasmaster 1 terminal PCB

No links supplied, use links from old PCB

E07109

Insulated Jumper links

Spare links for PCB's, minimum order quantity 10

S012304

Power supply assembly

Complete with wiring looms

S012205

Sounder assembly

Complete with wiring loom

M04683

Sounder seal

M050067

Gasmaster 4 display label

For front cover

M050068

Gasmaster 1 display label

For front cover

C01929

Communications Kit Includes

Gasmaster PC software, connection lead and RS485/232 converter.

E07635

Communications port

3-pin connector for fitment to Gasmaster to enable interface with the

Communications Kit. Comes complete with wiring loom for connection to

the RS-485 terminals.

S012303

Front cover assembly for Gasmaster 1

Complete with labels, sounder and seals

S012302

Front cover assembly for Gasmaster 4

Complete with labels, sounder and seals

M01861/2

Flush mounting brackets

For mounting Gasmaster into a panel.

S012207

4-20mA/Fire input module

S012208

mV Pellistor input module

Appendix B: Spare Parts and Accessories

Summary of Contents for Gasmaster














































Search results

Summary of Contents for Gasmaster

Reviews:

Related manuals for Gasmaster

Brands by name

Popular brands

GAS Gasmaster, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for Gasmaster

Reviews:

Related manuals for Gasmaster

Brands by name

Popular brands