GAS Gasmaster Installation, Operation And Maintenance Manual Download Page 27

Page: 27 / 45

Over the next few pages you will find a detailed

description of the menu system. Use figure 3.4 as an

overall guide to locate menu items.
Gasmaster has five standard menus: Faults, Warnings,

View, Actions and Supervisor. Only the Supervisor menu

allows you to configure Gasmaster.
This section contains tables that list the menu items for

each menu and the available values.

See “Using the Control Panel in Supervisor Mode” on

page 21 for instructions on how to alter settings.
Note: The display only shows two lines of information
at a time. Use the Up



and Down



buttons to see

additional menu items or values.

Use Continue



to select choices and Back



to exit

menu.

Faults menu

(lists faults present on the system)

Menu system overview

Menu Item

Values (as shown on display)

Description

Fault codes

No faults

(end of list)

No faults are present

Faults

Measurement system failure!

Fatal fault, contact us.

1 or 2

Warning - Battery low

Input supply has failed and internal battery supply has

dropped to 22 volts.

Relay power supply fail

Power rail to the relays has failed and relays will no longer

operate. Contact us.

Main supply fail

Main supply has failed and the system is running on

batteries

NVM hardware fail

Fatal fault, contact us.

Loaded default settings

System has returned to standard configuration settings.

Re-configure using the Supervisor menu.

Common relay fail

Coil fault detected. Contact us.

9, 10, 11

Chan #1 relay fail

Channel relay coil fault detected. Contact us.*

12 to 19

ESU #1 stalled!

ESU sampling device has stopped.*

20 to 23

ESU #1 slow!

ESU sampling device has slowed.*

24 to 27

Chan #1 over range

Detector input signal is over 21.5 mA. Investigate cause at

detector taking necessary precautions as high gas levels

may be present.*

28 to 31

Chan #1 under range

Detector input signal is under 3 mA. Check detector.* If the

‘Interpret 2 mA’ command is set to Warning or Inhibit in the

channel configuration, this fault message will display when

the input signal drops below 1mA.

32 to 35

Chan #n: pellistor saver mode

mV pellistor type detector has been exposed to gas in

excess of 95%LEL. A 200-second timer will be applied, after

which the fault may be reset *

36-39

* #1 denotes the channel number and therefore may read #2, #3 or #4 on Gasmaster.
The fault codes are numbered to relate to a particular channel where appropriate (e.g. fault code 19 means there is a

fault on Channel 4 Level 2 alarm relay).

Summary of Contents for Gasmaster














































Search results

Summary of Contents for Gasmaster

Reviews:

Related manuals for Gasmaster

Brands by name

Popular brands

GAS Gasmaster, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for Gasmaster

Reviews:

Related manuals for Gasmaster

Brands by name

Popular brands