background image

Part # 4529895 (01/31/08)

Page 9

INSTALLATION

Requirements of Installation

The underside and sides of the induction unit must be 
absolutely clear of obstructions to provide for adequate 
cooling air to enter and exhaust. Cooling air enters from the 
bottom of the unit and is discharged either from the sides 
(single or wok units) or from the rear (double units). An 
air intake kit is provided to ensure adequate cooling air is 
brought to the unit. A minimum of 30 sq inch opening must 
be provided for the heated air to be discharged into the 
room.

1

Make Sure that the induction unit does not take in hot 
ambient air (concerns units standing side by side, or one 
behind the other, or standing near a frying pan or oven).

2. The induction unit must not be placed near or on a hot 

surface.

3. Make sure that the induction unit does not take in grease 

laden air which is produced by other applications (deep 
fat fryer, grill, frying pan). In which case you must use an 
air an air duct (available as an accessory).

4. The air intake temperature must be under 104°F (40°).

5. The operating staff has to make sure that the installation, 

support and inspection is done by qualified personnel.

Installation Ambience

CONDITIONS

STORAGE

FUNCTION 

Max. Ambient 
Temperature

> -4°F (-20ºC) to 

158°F (70ºC)

> 41ºF (5ºC) to 

104ºF (40ºC)

Max. Relative 
Humidity Of Air

> -10% to 90%

> 30% to 90%

Electrical Connections

Turn the control knob to the OFF-position before connecting 
the cooker to the voltage supply.

The operator has to insure that all installation, maintenance 
and inspection work is carried out by authorized and 
qualified personnel.

1. Check and ensure that the supply voltage matches the 

voltage given on the specification plate.

2. The electrical connections must satisfy local house 

installation regulations. The valid national and local 
regulations must be observed.

3. The cooker is provided with a cord and plug (60 cycle 

units only).

Cut Out Opening

Louvered

Air Exhaust

Opening

(By Installer)

Aluminum air duct

(Max 96" (8'))

mounted on collars

with hose clamps

Removable grease filter and air

intake housing mounted on

cabinet

Fresh Air Supply

Air Intake Housing

See Fig. # 1

Sleeve with hose clip:

mounted to cabinet

Sleeve with hose clip:

mounted on bottom of unit

Silicone

Summary of Contents for GIU 2.5 BI









































Reviews: