background image

Part #4519655 Rev.2 (Jan 27/15)

Page 11

Top Sections

Griddle Top

Seasoning

 – Before being used for the fi rst time, all griddle 

surfaces must be seasoned. Was the griddle with a hot 
detergent or soap solution, rinse and dry thoroughly. Set 
the Griddle heat to the lowest possible temperature for 30 
minutes. Apply a thin fi lm of cooking oil. Allow the oil to 
remain on the griddle for 5 minutes and then wipe off . Rest 
the heat to medium temperature and apply a second fi lm 
of oil. Wipe off  excess after 5 minutes. Rest the heat to the 
cooking temperature and apply a fi nal fi lm of oil, wiping 
off  excess after 3 minutes. The griddle is now seasoned and 
ready for use. The griddle may be re-seasoned at any time by 
cleaning thoroughly and following the seasoning procedure.

Cleaning.

 – Griddle plates should be wiped daily while still 

warm. Remove carbonized grease or food with a spatula. 
When necessary, clean the griddle surface thoroughly using 
a fi ne griddle brick or a liquid griddle cleaner (available from 
your kitchen equipment dealer.). Polish the griddle surface 
to a bright fi nish. Wash the griddle surface, rinse and dry 
thoroughly. Re-season the griddle.

Operating Suggestions

1.  Avoid overheating the griddle as this causes sticking and 

grease carbonization resulting in a hard to clean surface. 

2.  Do not hit spatula on griddle plate as this will nick the 

surface

3.  Clean the grease tray often to eliminate spillovers.

CLEANING AND MAINTENANCE continued

Open Top

Porcelain Tops & Grates 

– Top grates should be washed daily 

with a hot detergent or soap solution and dried thoroughly.

Drop Pans

 – Should be emptied and washed daily

Operating Suggestions

1.  Avoid the use of oversized pots.

2. Avoid 

spillovers

3.  Covered pots will boil faster

Stock Pot Ranges

Cast Iron Top

 – When cast iron tops (which are covered in 

grease) arrive at the end users, the following seasoning and 
care is recommended. 

1.  Wash the top grates with hot mild detergent or soap 

solution. Dry thoroughly, rub with vegetable oil on all 
exposed surfaces in the direction of the grain.

2.   Soiled and burnt deposits can be removed with a wire 

brush. Diffi

  cult to remove burnt deposit can usually be 

removed using an oven cleaner. Wash, dry thoroughly, 
then rub with vegetable oil. 

3.  Continuing this procedure will prohibit the development 

of rust and will eventually form a non-stick surface, with 
the caramelization of oil on the cast iron top grates. 

Cleaning 

– Use a hot mild detergent or soap solution to 

clean the exterior daily. Dry thoroughly.

 

Summary of Contents for G24 SERIES

























Reviews: