![background image](http://html1.mh-extra.com/html/garland/cs-best-100/cs-best-100_instruction-manual_3592235030.webp)
English
30/108
English
31/108
New chains need some time until the teeth adapt
and this could modify slightly the length of the chain.
This adaptation takes only a couple of minyes when
in use. If you have just changed the chain, remember
to check the tension of the chain after a couple of
minutes using the machine.
5.2.2. CHAIN OIL
Only use oil specfically recommended for chainsaws.
Do not use already used oils or oils with impurities as
this could damage the oil pump of the machine.
The chain oil must be introduced in the chain oil
deposit. The oil deposit cap is indicated in chapter 3.
“Machine symbols”.
To avoid dirt and impurities entering the interior of the
deposit, clean the oil cap of the deposit before opening
it.
Close the cap of the oil level and clean if any oil has
fallen outside the deposit.
Check the level of the oil by looking at the oil level
gauge.
Note: The life span of the chain and bar guides depends
on the quality of the oil used. Do not use old or already
used oil! Only use oil that does not damage your
surroundings. Only store oil in homologated recipients.
5.3. START UP
5.3.1. POINTS TO BE CHECKED PRIOR TO USING THE
MACHINE
Check the machine and ensure all nuts are tightly
secured, there are no lose pieces. Replace or repair
any broken pieces that you may have seen to be in a
bad state. Ensue there are no oil leakages. Do not use
the machine if damaged or incorrectly regulated.
Only use this machine for those jobs it has been
designed to do. The use of this machine for any other
use is dangerous and could cause damages to you
and/or the machine.
Check the machine completely and look for loose and
damaged parts (screws, nuts).
Tighten, repair or replace everything you need before
using the machine.
Do not use other accessories this machine except
those recommended by our company since its use
could cause severe damage to the user, people close
to the machine and the machine itself.
Before start up, remove the security blade protector
from the blade.
Check that the moving parts of the machine are not in
contact with any object.
5.3.2. CHECKPOINTS AFTER STARTING THE MACHINE
It is necessary to pay attention to the possible loosening
or overheating of the parts of the machine. If you detect
any anomaly immediately stop the machine and check
it carefully. In case of mechanical failure take the
machine to the technical service for repair. You should
not continue working if you notice that the operation is
not correct.
Do not use the machine if it is damaged or
improperly adjusted.
VERIFYING THE OIL LUBRICATION SYSTEM
After start up, accelerate the prunner until the chain
rotates at a medium speed and verify that the prunner
has oil lubrication. To check this, place the machine
Summary of Contents for CS BEST 100
