![background image](http://html1.mh-extra.com/html/gardner-denver/reavell-h5000-series/reavell-h5000-series_operators-handbook-manual_3870357082.webp)
ANCILLARY PARTS
PAGE 80
CONTROLLER
PART No
TRIP POINTER
STOP SETTING °C
USED ON
COMPRESSOR MODEL
C202556.1 125
5236.1
C202556.2 140
5212
C202556.3 150
5336,5415
C202556.4
155
5215 & 5217
C202556.5 170
5236.2,5315
C202556.6 180
5415E5317,5417.5417N
C202556.7 205
5436(CU
TUBES)
C202556.8
220
5436.1 &.2,5436H,5436N,5436SN & 5437
C202749.1 200
5280
C202749.2 210
5280
C202749.3 175
5409
C202960.1
75
WATERCOOLED M/C’S DELIVERY
C202960.2 60
5211
C202960.3 55
WATER
OUTLET
C202960.4 80
5207,5209,5213
C202960.5 50
5417N,5436N
C202964.1 75
5280,5281,5282,5283,
DELY
C202964.2 60
5450,5470
DELY
CONTROLLER
PART No
TEMPERATURE RANGE
°C
USED ON
COMPRESSOR MODEL
98288.1089
50 - 250
WATERCOOLED 5000 SERIES
98288.1121
0 - 120
WATERCOOLED 5000 SERIES
CONTROLLER
PART No
WHERE FITTED
USED ON
COMPRESSOR MODEL
98288.1093
1st – 5th STG. DELIVERY
5450 & 5470
98288.1094
FINAL DELIVERY
5450 & 5470
98288.1215
THE PURPOSE OF THIS SWITCH IS TO PREVENT THE COMPRESSOR FROM STARTING IN LOWER
THAN RECOMMENDED AMBIENT TEMPERATURES.IT IS FITTED AT THE COMPRESSOR GAS INLET
PORT.THE MINIMUM TEMPERATURE OF -10°C HAS BEEN SET AT THE FACTORY, BUT THIS CAN BE
RAISED ON SITE IF REQUIRED BY FOLLOWING THE PROCEDURE BELOW.
TO SET.
RELEASE ADJUSTING KEY (A) FROM BACK OF INSTRUMENT BY REMOVING SECURING NUT.
INSERT END OF KEY INTO CENTRAL ADJUSTER KNOB (B) AND TURN TO ADJUST SET POINTER TO
REQUIRED MINIMUM TEMPERATURE
ABOVE -10°C.
REPLACE ADJUSTING KEY AND SECURE WITH NUT.
CONTROLLER
PART No
TEMPERATURE
RANGE
TRIP POINTER
STOP SETTING °C
USED ON
COMPRESSOR MODEL
98288.1215
-40° / +80°C
-10°C FALLING
5000 SERIES WATER-COOLED
COMPRESSORS
A
TYPICAL
SWITCH DIAL
B
Summary of Contents for Reavell H5000 Series
