background image

 

 

 

General Information 

These compressors are for compressing atmospheric air and are not suitable for compressing any other gas. They are 
designed and manufactured to give optimum performance with long life and reliability.  

This manual gives the user all the information required to install and operate the compressors and carry out the regular 
schedules for servicing and maintenance, which will ensure the maximum satisfactory service life.  

Servicing facilities and the supply of genuine replacement parts are provided through a worldwide network of Gardner 
Denver Companies and Distributors. If replacement parts are needed, the user should, in the first instance, contact the 
local Gardner Denver Company or Distributor.  

The information given in this manual was correct at the time of printing, however, as part of continuous development, 
modifications to parts and procedures may be made without notice which could affect the servicing requirements of the 
compressors. Before any servicing or maintenance work is undertaken the user is advised to contact the local Gardner 
Denver Company or Distributor who is supplied with revised and up-dated information.  

In any communication concerning the compressor it is essential to quote the MODEL, SERIAL NUMBER and where 
possible the YEAR of MANUFACTURE.  

All pressure data given in this manual refer to overpressures (pressure gauge pressures) unless specified otherwise.  

 

Maintenance 

To ensure the continued trouble-free operation of the compressor unit it is important that periodic maintenance and 
servicing is carried out in accordance with the information given in the ‘Maintenance’ section of this manual. To assist in 
this matter your local Gardner Denver Company or Distributor can provide a number of optional maintenance 
agreements to suit your requirements. These agreements provide the user with the expertise of our factory trained 
technicians and the guarantee that only Genuine Gardner Denver parts will be used.  

 

Warranty 

The conditions of the Gardner Denver Warranty are set out in the Company’s standard Conditions of Sale available from 
the Gardner Denver Company or Distributor supplying the machine. 

 

 

USE ONLY GARDNER DENVER GENUINE PARTS. YOUR WARRANTY COULD 
BE AFFECTED IF A SERVICE OR REPAIR IS CARRIED OUT USING  
NON-GENUINE PARTS.

 

 

 

 

 

Summary of Contents for L07





























































Reviews: