background image

GAT NET.Lock 7000 System 
Configuration and Operation 

www.gantner.com

  

HB_GAT-NETLOCK7000--EN_30

 

33

 

 

5.5  Status Information at GAT NET.Controller S 7000 and GAT NET.Controller M 7000 

 
 

  

 
 
LED 2 shows the following status information at a slave and master controller. 
 
 

5.5.1  Slave Controller 

 

LED 2 

Status Information 

red 

Emergency operation (no connection, neither to the master controller nor to the server/software) 

red blinking 

Emergency operation (connection to master controller OK, but no connection to server/software) 

green 

Normal operation (connection to master controller and server/software is OK) 

alternately  red/green 

blinking 

Bootloader mode (a firmware update is currently being loaded or there is no firmware present in the 

controller) 

 

Table 5.1 

 - Status information at a slave controller GAT NET.Controller S 7000 

 
 
 

5.5.2  Master Controller 

 

LED 2 

Status Information 

red 

Emergency operation (no connection to the server/software) 

green 

Normal operation (connection to server/software is OK) 

alternately  red/green 

blinking 

Bootloader mode (a firmware update is currently being loaded or there is no firmware present in the 

controller) 

 

Table 5.2

 

 

 - Status information at a master controller GAT NET.Controller M 7000 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for GAT NET.Lock 7000









































Reviews: