Gamry Instruments TDC4 Operator'S Manual Download Page 2

 

Limited Warranty 

Gamry Instruments, Inc. warrants to the original user of this product that it shall be free of defects 
resulting from faulty manufacture of the product or its components for a period of two years from the 
date of shipment. 

Gamry Instruments, Inc. makes no warranties regarding either the satisfactory performance of the 
TDC4 Temperature Controller including the software used with this product or the fitness of TDC4 
based systems for any particular purpose.  The remedy for breach of this Limited Warranty shall be 
limited solely to repair or by replacement, as determined by Gamry Instruments, Inc., and shall not 
include other damages. 

Gamry Instruments, Inc. reserves the right to make revisions to the TDC4 at any time without 
incurring any obligation to install same on TDC4s previously purchased.  All system specifications are 
subject  to change without notice. 

There are no warranties which extend beyond the description herein.  This warranty is in lieu 
of, and excludes any and all other warranties or representations, expressed, implied or 
statutory, including merchantability and fitness, as well as any and all other obligations or 
liabilities of Gamry Instruments, Inc., including but not limited to, special or consequential 
damages. 

This limited warranty gives you specific legal rights and you may have others which vary from state to 
state.   Some states do not allow for the exclusion of incidental or consequential damages. 

No person, firm or corporation is authorized to assume for Gamry Instruments, Inc. any additional 
obligation or liability not expressly provided herein except in writing duly executed by an officer of 
Gamry Instruments, Inc. 
 

Summary of Contents for TDC4

































Reviews: