background image

22.

23

Solenoid Control Error

This indicates that an attempt was made to open or close a solenoid valve when it was already in
that state (according to the software). It will also occur (except in diagnostic mode) if an attempt is
made to turn on a solenoid valve when the corresponding motor is not on.

24

Power Fail

This error indicates the system entered its main initialisation procedure (which should only happen
on power up or as a result of certain diagnostic functions), but the power fail flag does not show
power failed.
This may occur in the event of a total power loss (including the lithium battery) such that the
XRAM was corrupted, or if the power fail procedures are not functioning correctly.

25

Input Processor to main failure

This error will occur if the system expects an Input Processor to be present (i.e., it was auto-
detected at power up) but is no longer receiving any comms response from it.
This would be caused by either a fatal error in the input processor, or a physical loss of connection
on the serial link between the two processor boards.

26

Main to Input Processor failure

This error will occur if the system expects an Input Processor to be present (i.e., it was auto-
detected at power up) and is receiving comms response from it, but the Input Processor is not
receiving data from the main processor.

This would be caused by either a fatal error in the input processor, or a physical loss of connection
on the serial link between the two processor boards.

27

Remote Parameters Failure

Error 27 will be displayed if the pump is not within the diagnostics functions and the remote
rx_param block that was sent from the input microprocessor is different to the set stored by the
you.

28

Display pointers corrupted

A constant check is dynamically made, of the display information.  This error indicates an error
has occurred which could cause incorrect information to be displayed on the LCDs.

29

Not used

These error codes are reserved.

Summary of Contents for Apollo 3000


















































































Reviews: