manualshive.com logo in svg

Galil Motion Control RIO-47 series RIO-47100, User Manual

Share
Download
Galil Motion Control RIO-47 series RIO-47100 User Manual Download Page 21

When the RIO acts as the master, the 

IH

 command is used to assign handles and connect to its slaves.

The IP address may be entered as a 4 byte number separated with commas (industry standard uses 
periods) or as a signed 32 bit number.  A port number may also be specified, but if it is not, it will 
default to 1000.  The protocol (TCP/IP or UDP/IP) to use must also be designated at this time.  

Otherwise, the board will not connect to the slave.  (Ex:  

IH

B

= 

151

,

25

,

255

,

9<179>2

.  This will 

open handle #2 and connect to the IP address 151.25.255.9, port 179, using TCP/IP)
Once the 

IH

 command is used to connect to slaves, the user can communicate to these slaves by 

sending commands to the master.  The 

SA

 command is used for this purpose, and it has the following 

syntax.

SA

h

=

 

"command string"

Here "command string" will be sent to handle h.  For example,  

SA

A

=

 

"XQ"

 command will send an 

XQ

command to the slave/server on handle A.  A more flexible form of the command is

SA

h= field1,field2,field3,field4 ... field8

where each field can be a string in quotes or a variable.  
When the Master/client sends an 

SA

 command to a Slave/server, it is possible for the master to 

determine the status of the command.  The response 

_IH

h

4

 will return the number 1 to 4.  1 

indicates waiting for the acknowledgement from the slave.  2 indicates a colon (command accepted) 
has been received.  3 indicates a question mark (command rejected) has been received.  4 indicates 
the communication timed out.
If a command generates multiple responses (such as the 

TE

 command), the values will be stored in 

_SA

h

0

 thru 

_SA

h

n

 where n is the last field.  If a field is unused, its 

_SA

 value will be -2^31.

See the Command Reference for more information on the 

SA

 command.

The RIO can communicate through its different channels, which can be tightly controlled.  When a 
device queries the RIO, it will receive the response unless it explicitly tells the RIO to send it to 
another device.  When a command that generates an unsolicited response is part of a downloaded 
program, the response will route to whichever port is specified by the 

CF

 command (either a specific 

Ethernet handle or the RS232 port). If the user wants to send the message to a port other than what 
is specified by the 

CF

 command, add an 

{Eh}

 or 

{P1}

 to the end of the command (Ex.  

MG 

{EB}

"Hello"

 will send the message "Hello" to handle #2 and 

MG 

{P1}

"Hello"

 will send it to the 

serial port).

Handling Communication Errors

A reserved automatic subroutine, which is identified by the label 

#TCPERR

, can be used to catch 

communication errors.  If an RIO has an application program running and the TCP communication is 
lost, the 

#TCPERR

 routine will automatically execute.  The 

#TCPERR

 routine should be ended with 

the 

RE

 command.  

Multicasting

A multicast may only be used in UDP/IP and is similar to a broadcast (where everyone on the network
gets the information) but specific to a group.  In other words, all devices within a specified group will 
receive the information that is sent in a multicast.  There can be many multicast groups on a network 
and are differentiated by their multicast IP address.  To communicate with all the devices in a specific 
multicast group, the information can be sent to the multicast IP address rather than to each 
individual device IP address.  All Galil devices belong to a default multicast address of 239.255.19.56.  
This multicast IP address can be changed by using the 

IA 

>

u

 command.

Chapter 3 Communication ▫  21                                                                                                                                                     RIO-47xxx Rev 1.0r

Summary of Contents for RIO-47 series RIO-47100





















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands