background image

96833 v.2.0

   

33

Gauges

There are five (5) gauges displayed 

in the Economy Environment. See 

Figure 31

. The three (3) to the left 

of the screen can be changed to 

display the data from a list of available 

parameters. The two (2) on the right, 

Instant MPG and Average MPG, can be 

changed only to increase or decrease 

the scale display.  Refer to ‘Gauge 

Placement’ in selection 15 to change 

the Gauges displayed.

Trip

The Trip feature will keep track of your 

vehicles Average Speed, Trip Distance, 

Trip Time, Engine On Time, cost per 

Trip, Fuel Used, MPH, Instant MPG, & 

Average MPG. You can switch between 

two (2) Trip recordings, ‘Trip A’ and 

‘Trip B’, by pressing the letter on the 

lower right corner of the Economy 

Environment screen. See 

Figure 31

You can view all this information by 

pressing on the wrench icon in the 

lower left corner of your screen. In 

the ‘Options’ menu press on the Trip 

information you wish to view. Once 

you have viewed the information, press 

the return icon to return to the Options 

menu or press the iQ icon to return to 

the Economy Environment. 

Reset trip Information

The Trip information data can be reset 

by pressing and holding the letter 

of the trip you wish to clear for 5 

seconds on the lower right corner of 

the Economy Environment screen. You 

may also reset the trip information by 

going to the trip data screen for each 

screen and press the ‘Reset’ button on 

the lower right corner. 

See Figure 32

.

Trip A has the option to reset 

automatically. All the data captured 

will be reset to zero after the engine 

has been off for more than two (2) 

hours. To enable this option press on 

the wrench icon in the lower left hand 

side of the screen of the Economy 

Environment screen. In the ‘Options’ 

menu press on the ‘Trip A’ tab. In the 

lower part of the Trip A screen press 

‘Auto’ to have the iQ automatically 

reset the trip information or press 

‘Manual’ to manually reset the 

information. See 

Figure 32

. Press the 

‘Return’ icon to return to the ‘Options’ 

menu or press the ‘iQ’ icon to return to 

the Economy Environment. 

-END, SEcTION 13-

Summary of Contents for Banks iQ





















































Reviews: