background image

 

SAFETY RULES 

General Rules 

1)

 

Read  this  manual  before  operating 
this tool 

and use common sense. 

 

2)

 

Stay  Alert, 

do  not  operate  this 

machine  when  you  are  drowsy, 
distracted.  Do  not  operate  this  tool 
when under the influences of drugs, 
alcohol, or medication. 

 

3)

 

Turn off machine before unplugging 

to avoid accidental start-up.

 

4)

 

Always wear safety equipment

 such 

as  eye  goggles,  ear  protection,  and 
dusk mask.  

 

5)

 

Keep your work area clean, well lit, 
dry, and free of distractions.  

6)

 

Never  use  power  tools  near 
explosive  gases,  liquids  or  in 
explosive  atmospheres. 

This  tool 

creates  sparks  that  would  ignite 
fumes. 

 

7)

 

Periodically inspect power cord. 

Do 

not use the power cord to carry, pull, 
or  unplug  the  tool.  Damaged  cords 
increase the risk of electrical shock. 

 

8)

 

Never  start  tool  when  any  rotating 
portion is in contact with any other 
object.  

9)

 

Only  use  correct  corresponding 
electrical  devices.

  Do  not  tamper 

with plugin or outlets. 

 

10)

 

Keep  machine  clean  and  dry. 

Use  a 

clean  cloth  to  clean.  Never  use 
gasoline,  brake  fluid,  petroleum-
based products, or any hard solvent 
to clean this machine. 

 

11)

 

Maintain the tool with care. 

Follow 

instructions  for  lubricating  and 
changing  accessories.  Keep  your 
tools sharp and clean. 

 

12)

 

 

 Do  not  force  the  tool.

  Allow  the 

machine to work at a steady safe rate. 

 

13)

 

Childproof  your work  area 

by  using 

appropriate locks, and keys. 

 

14)

 

Save  this  manual  for  future 
reference.  

SPECIFIC RULES FOR OPERATING THIS DRILL PRESS 

California proposition 65 

This product and dust created by power sanding, sawing, grinding, drilling, and other construction 
activities may contain chemicals, including lead, known to the State of California to cause cancer, 
birth defects, or other reproductive harm. 

Wash hands after handling.

  

Some Examples of these chemicals are:  

 

lead from lead-based paints, 

 

crystalline silica from bricks, cement, and other masonry products, and  

 

arsenic and chromium from chemically treated lumber.  

Your risk from these exposures varies depending on how often you do this type of work. To reduce 
your expose to these chemicals, work in a well-ventilated area with approved safety equipment such 
as a dusk mask specially designed to filter out microscopic particles. 

 

Summary of Contents for FY4116Q












Reviews: