FUTABA FMT-03 Instruction Manual Download Page 16

Page: 16 / 68

<Before Use>

CAUTION

Be sure to install an antenna and do a

flight.

■

When there are no antennas, you can't control.

Please do not grasp the transmitter's

antenna during flight.

■

Doing so may degrade the quality of the RF

transmission to the model.

Do not carry the transmitter by the

antenna.

■

There is the danger that the antenna wire will break

and operation will become impossible.

Do not pull the antenna forcefully.

■

There is the danger that the antenna wire will break

and operation will become impossible.

Attachment and removal of an antenna

FMT-03 can attach or remove an antenna.

Dust and water aren't supposed to be stuck in an

antenna connector.

Antenna screw

Rotation part

Install of an antenna

straight to a screw.

Tighten a screw tightly

so as not to loosen.

Antenna

This nut isn't

removed.

Summary of Contents for FMT-03





































































Search results

Summary of Contents for FMT-03

Reviews:

Related manuals for FMT-03

Brands by name

Popular brands

FUTABA FMT-03, Instruction Manual

Search results

Summary of Contents for FMT-03

Reviews:

Related manuals for FMT-03

Brands by name

Popular brands