Furukawa Unic URW376C4U -T Series Operation & Maintenance Manual Download Page 45

Page: 45 / 156

9-9

DESCRIPTION OF EACH CONTROL DEVICE

The meter shows weight of a cargo being
hoisted. Read the scale corresponding to the
number of wire rope hooking.

Load meter

Load meter is secured on the panel

• Remarks

◆

Dial of the load meter has:

• Scale bands corresponding to A, B, C, and

D of the “load indicator” for 4-rope hook-
ing system, and

• Scale band for single-rope hooking sys-

tem.

★

“Load meter” indicates the

weight of a hoisted cargo only
while the hook is winding up
and does not indicate the weight
at the time of other operations
including when winding up is
stopped and unwinding.

★

Take the weight indicated on

the load meter as an approximate
value.

CAUTION

Load meter

Number of ropes
being hooked

Ⲵ䚷㔜䚷ィ

䠟

䠠

䠐䠢䠝䠨䠨䠯

䠍䠢䠝䠨䠨

䠐䠢䠝䠨䠨䠯

ᮏ᥃

䠐

䠍

䠏䠌䠩䠌䠒䠑䠌䠍䠌

Summary of Contents for URW376C4U -T Series





























































































































































Search results

Summary of Contents for URW376C4U -T Series

Reviews:

Brands by name

Popular brands

Furukawa Unic URW376C4U -T Series, Operation & Maintenance Manual

Search results

Summary of Contents for URW376C4U -T Series

Reviews:

Brands by name

Popular brands