manualshive.com logo in svg

Furukawa Unic URW376C4U -T Series, Operation & Maintenance Manual

Share
Download
Furukawa Unic URW376C4U -T Series Operation & Maintenance Manual Download Page 131

13-3

MAINTENANCE AND INSPECTION OF CRANE

When the slewing device makes an unusual 
noise while operating or crawling the crane, 
or when a gap is created on the mounting sur-
face, contact a UNIC authorized service shop 
for inspection and/ for repair. 

Keep the crane clean at any time.
Sands and fine dusts may cause an abnormal wear.
Do not wash the crane by splashing highly pressurized water to prevent it from entering into the 
electric system which may cause malfunction of the crane.

 Cleaning

 Inspection of bolts mounting slewing bearings

 

★

Break of the bolts mount-

ing slewing bearings invite an 
accident such as overturn and 
destruction of the crane. 
Check the mounting bolts (outer 
ring side) for tightness once 
every 6 months.

CAUTION

Summary of Contents for URW376C4U -T Series





























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands