Furukawa Unic URW376C4U -T Series Operation & Maintenance Manual Download Page 107

Page: 107 / 156

12-15

MAINTENANCE AND INSPECTION OF CARRIER

◆

Check for air cleaner element
/ Cleaning

★

Do not make a cleaning and a replacement of air cleaner while engine

is running.

★

If the crane is operated in dusty environment, shorten accordingly

the time when making inspection and cleaning.

Check and clean the air cleaner element when
the crane has been operated for 250 hours (3
months) or when the lamp for warning clog-
ging of air cleaner element lights.

WARNING

CAUTION

Clamp

Dust cup

Take out the outer air cleaner element
only to check and clean the element.

Element

Unfasten the clamp to remove the dust
cup.

Summary of Contents for URW376C4U -T Series





























































































































































Search results

Summary of Contents for URW376C4U -T Series

Reviews:

Brands by name

Popular brands

Furukawa Unic URW376C4U -T Series, Operation & Maintenance Manual

Search results

Summary of Contents for URW376C4U -T Series

Reviews:

Brands by name

Popular brands