657-110001
Page
3
Figure 2 Heat sink orientation
INSTALLATION INSTRUCTIONS
WARNING
This control should only be installed by a qualified technician, electrician or electrical maintenance
person familiar with its operation and associated hazards. The National Electrical Code (NEC), local
electrical and safety codes, and when applicable, the Occupational Safety and Health Act (OSHA) should
be observed to reduce hazards to personnel and property. The user must provide a proper enclosure for
chassis type controls.
Circuitry is not at ground potential. Do not perform work on or near the control while it is connected to
the AC line.
CAUTION
Exposed circuit boards should be protected from electrostatic discharge. The control board uses CMOS
circuitry. Static discharge into the control board must be avoided to prevent component damage.
Mounting the Control
The mounting template (provided in the
center of this manual) can be used to
position and mark the location of
mounting holes on the surface where the
control is to be located. The control
should be mounted vertically, using the
slots on either the narrow or wide
surfaces of the heatsink. This
arrangement provides optimum air flow
around the control. See Figure 2.
Electrical connections
Read the following instructions as well as
all of the applicable safety
recommendations, before making any
electrical connections between the
control, motor, or motion control
electronics.
WARNING
The 115 VAC power line to the control should be the very last connection made. Disconnect the
power line before making any other electrical connections.
Summary of Contents for LA-309
