Fujitsu XG0224 User Manual Download Page 394

Page: 394 / 631

XG Series User's Guide

Chapter 5 Command Reference

Ethernet Counter, Log, Statistics, and Status Display and Clear Operation

Commands

394

5.20.1.2 show ether brief

Function

Display the information about Ethernet physical ports briefly.

Available Model

XG0224 / XG0448 / XG0440DC / XG0440DCR / XG2600

Syntax

show ether brief

Options

N/A

Display all information.

Use Mode

Operation mode (user class/admin class)
Configuration mode (admin class)

Explanation

Display the Ethernet port information briefly.

Execution Example

Port number

Port state

: Indicates that the port is in the linkup state.

down

: Indicates that the port is in the linkdown state.

standby : Indicates that the port is in the standby state. (backup port only)

"*standby" is displayed when the port is not established (not
switched) as a standby port in the linkup state.

offline

: Indicates that the port is in the offline state.

disable

: Indicates that the port is not used based on the definition.

Port type

normal

: Indicates that the port is used as a normal port.

mirror

: Indicates that the port is used as a target port for mirroring.

# show ether brief

port status type media mdi speed duplex flow

----- -------- ------------------ ------ ----- ------ ------- -----

(1) (2) (3) (4) (5) (6) (7) (8)

1 up normal metal MDIX 1000M full TxRx

2 up normal metal MDI 1000M full Rx

3 up linkaggregation1 metal - 1000M full TxRx

4 up linkaggregation1 metal - 1000M full TxRx

5 up linkaggregation1 metal - 1000M full TxRx

6 up linkaggregation1 metal - 1000M full TxRx

7 offline normal - - - - -

8 up backup1 metal MDIX 1000M full -

9 standby backup1 metal MDIX 1000M full -

10 down normal - - - - -

11 down normal - - - - -

12 up linkaggregation4 metal MDIX 1000M full Tx

13 up linkaggregation4 metal MDIX 1000M full Tx

14 disable normal - - - - -

15 disable normal - - - - -

16 down mirror - - - - -

17 up normal metal MDIX 1000M full Rx

18 up normal metal MDIX 1000M full Rx

19 up normal metal MDIX 1000M full Rx

20 up normal metal MDIX 1000M full Rx

21 up normal metal - 1000M full Rx

22 up normal metal - 1000M full Rx

23 up normal metal - 1000M full Rx

24 up normal metal - 1000M full Rx

25 up normal metal - 1000M full Rx

26 up normal metal - 1000M full Rx

Summary of Contents for XG0224
























































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for XG0224

Reviews:

Related manuals for XG0224

Brands by name

Popular brands

Fujitsu XG0224, User Manual

Search results

Summary of Contents for XG0224

Reviews:

Related manuals for XG0224

Brands by name

Popular brands