Home
/
Fujitsu
/
XG0224
/
User Manual

Fujitsu XG0224, User Manual, Page: 176 / 631

Share

Page: 176 / 631

Fujitsu XG0224 User Manual Download Page 176

XG Series User's Guide

Chapter 5 Command Reference

VLAN Information Settings

176

If "dscp" is selected in <action>:

- <dscp_value>

Set the replaced "dscp" value with a decimal value from 0 to 63.

If "tos" is selected in <action>:

- <tos_value>

Set the replaced "ip precedence" value with a decimal value from 0 to 7.

- cos

Replace the "ip precedence" value with the "cos" value.

If "queue" is selected in <action>:

- <queue_value>

Specify a queue number of the output port to be used.
A larger value indicates a queue with a higher output priority.

<acl>
•

ACL definition number
Specify the ACL definition number of the access control list where the packet pattern to
configure QoS conversion has been defined.

Use Mode

Configuration mode (admin class)

Explanation

Set the QoS (quality of service) of each Ethernet port.
For the ingress packets that match the "acl mac", "acl vlan", "acl ip", "acl icmp", "acl tcp",
or "acl udp" definitions of the access control list which has been specified by <acl>, the
QoS processing is executed in the way as specified by <action>.

Caution

Note 1.

If none of "acl mac", "acl vlan" and "acl ip" definitions exist on the access control list
which has been specified by <acl> or if the access control list specified by <acl> does not
exist, the packets are not filtered.

[XG2600]
Note 2.

If a queue is selected by <action> and if this queue has not been associated with the cos
value by the

"ether qos prioritymap"

command, the QoS processing is not executed.

Note 3.

"acl mac llc" definitions can not filter llc frames with the VLAN tag.

Note 4.

This command is unavailable if the allowable upper limit for the device is exceeded.
The allowable upper limits are as follows.

•

Upper limit based on "commands"
64 commands for the entire device.
Up to 64 commands can be set for the entire device, including the

"ether macfilter"

"vlan macfilter"

"lan ip filter"

"ether qos aclmap"

"vlan qos aclmap"

commands.
The priority for each command is as follows.

Range

Model

0 to 7

XG0224 / XG0448 / XG0440DC / XG0440DCR / XG2600

«
...
174
175
176
177
178
...
»

Summary of Contents for XG0224
























































































































































































































































































































































































































































































































































































































































Reviews:

No comments