manualshive.com logo in svg

Fujitsu PRIMERGY TX300, Operating Manual, Page: 86 / 127

Share
Download
Fujitsu PRIMERGY TX300 Operating Manual Download Page 86

80

 

 A26361-K881-Z102-4-7619

Hot-swap Power Supply Units

Hot-plug/hot-swap Components

8.1.2

Replacing a Hot-swap Power Supply Unit

Figure 29: Unlocking and removing the power supply unit

V

CAUTION!

Before replacing a non defective power supply unit in a non-redundant 
configuration (only one power supply unit present) the server must be 
switched OFF.

Ê

Remove the cable from the installed power supply unit.

Ê

Turn the transport lock (a) 45° counterclockwise (1) and pull it out (2).

Ê

Slide the locking bar of the installed power supply unit towards the power 
plug (3) and remove the power supply unit from the mounting location in the 
direction marked (4).

Ê

Open the transport lock of the new power supply unit, insert and lock it into 
the free mounting location in the reverse order.

I

Make sure that the power supply unit engages correctly in the mounting 
frame and is locked in position.

This is the only way to avoid the power supply unit being shaken out of 
its mountings and damaged during transport.

Ê

Connect up the power supply unit.

a

2

3

1

4

Summary of Contents for PRIMERGY TX300
































































































































Reviews:

No comments