manualshive.com logo in svg

Fujitsu PRIMERGY TX300, Operating Manual, Page: 72 / 127

Share
Download
Fujitsu PRIMERGY TX300 Operating Manual Download Page 72

66

 

 A26361-K881-Z102-4-7619

Configuring the Server

Preparation for Use and Operation

5.5

Configuring the Server

This section contains information about configuring the server and installing the 
operating system.

I

Make sure that the energy saving functions are disabled in the 

BIOS Setup

 

during server operation.

5.5.1

Configuration with ServerStart

Configuring HostRAID

The server is equipped with an onboard Ultra320 SCSI controller with HostRAID 
functionality. Configure HostRAID before you begin with 

ServerStart

.

I

To configure HostRAID the controller has its own RAID-Select Utility. For 
further information see “Adaptec HostRAID User’s Guide“ on the 

Server-

Books

 CD (choose 

Controllers

 from the menu).

With the 

ServerStart

-CD provided, you can configure the server and install the 

operating system in a convenient manner. The menu-guided configuration 
includes the server configuration with the 

SCU

 and the RAID controller configu-

ration with the 

GAM

 (Global Array Manager) and/or Adaptec Storage Manager.

I

Descriptions of operating systems not covered in the RAID controller 
manual are provided in the appropriate readme files on the driver 
diskettes.

To find out how to operate 

ServerStart

 and for further information, refer to the 

corresponding CD booklet (see “Related Publications” on page 107).

If you use 

ServerStart

, you can skip the following section on how to configure the 

server and install the operating system. Continue with section “Cleaning the 
Server” on page 68.

Summary of Contents for PRIMERGY TX300
































































































































Reviews:

No comments