manualshive.com logo in svg

Fujitsu PRIMERGY TX300, Operating Manual, Page: 68 / 127

Share
Download
Fujitsu PRIMERGY TX300 Operating Manual Download Page 68

62

 

 A26361-K881-Z102-4-7619

Operating and Indicator Elements

Preparation for Use and Operation

Indicators for hot-plug PCI slots 

The indicators ((b) and (c) on figure 39 on page 95) are located on the card 
guide on the inside of the server.

The indicators on these slots behave differently depending on whether (table 3) 
or not the operating system supports hot-plug functionality (table 4 on page 63):

Pos.

Power 

indicator 

(green)

Error 

indicator 

(orange)

Status description

1

does not 

light

does not 

light

1. Device switched off.

2. Device operating but PCI slot not powered 

up. One board may be installed or 
removed.

2

flashing

does not 

light

Device operating.

PCI slot is in enable or disable sequence. 

Wait until the green LED has changed its 
status (does not light after disable or lights 
after enable sequence).

3

lights

does not 

light

Device operating.

PCI slot powered up. No board may be 
installed or removed.

4

does not 

light

lights

Device operating: a problem has occurred.

There are two possible causes for this status:

–

The MRL sensor was pressed without 
authorization. This status cannot be exited 
(NMI initiated: see section “Hot-Plug PCI 
Error Indicator Lighting” on page 76).

–

There was a power failure during the 
enable sequence (the PCI slot is reset to 
disable status).

Table 3: Operating system with hot-plug functionality: hot-plug PCI indicator modes

Summary of Contents for PRIMERGY TX300
































































































































Reviews:

No comments