manualshive.com logo in svg

Fujitsu PRIMERGY TX300, Operating Manual, Page: 62 / 127

Share
Download
Fujitsu PRIMERGY TX300 Operating Manual Download Page 62

56

 

 A26361-K881-Z102-4-7619

Operating and Indicator Elements

Preparation for Use and Operation

Operating elements

Lock

The server can be locked to prevent access to the drives:

Server unlocked: the drives can be accessed.

Server locked: the drives can not be accessed.

ON/OFF button

When the system is switched OFF, it can be switched ON again by 
pressing the ON/OFF button. When the system is operating, pressing 
the ON/OFF button will switch OFF the system.

I

The ON/OFF button does not disconnect the server from the 
mains. To disconnect from the mains completely, remove the 
power plug.

NMI

NMI button

V

CAUTION!

Please do not press! Risk of losing data!

The NMI button may only be used by Service.

reset

Reset button

Pressing the reset button reboots the system.

V

CAUTION!

Risk of losing data!

ID

Identification (ID) button

The ID indicators on the front and on the rear of the server lights up 
(blue) when the ID button is pressed. The two ID indicators are 
synchronized.

Summary of Contents for PRIMERGY TX300
































































































































Reviews:

No comments