Fujitsu PRIMERGY TX300 Operating Manual Download Page 69

Page: 69 / 127

A26361-K881-Z102-4-7619

Preparation for Use and Operation

Switching the Server ON and OFF

5.3

Switching the Server ON and OFF

CAUTION!

If after switching ON the server there is nothing but flickering stripes on
the screen, switch the server OFF immediately (see chapter “Trouble-
shooting and Tips” on page 71).

The ON/OFF button does not disconnect the server from the mains. To
disconnect from the mains completely, remove the power plug.

Switching the server ON

–

First system installation:

Press the ON/OFF button (position 1in figure 24 on page 55).

Insert the

ServerStart

-CD and/or an installation disk in the corresponding

drive.

Follow the instructions on the monitor (see also section “Configuration
with ServerStart” on page 66 and/or section “Configuration without
ServerStart” on page 67).

–

System already installed:

The power-on indicator (position 2in figure 24 on page 55) lights orange
(standby mode).

Press the ON/OFF button (position 1in figure 24 on page 55).

The server is switched ON, performs a system test and boots the
operating system.

Pos.

Power

indicator

(green)

Error

indicator

(orange)

Status description

does not

light

does not

light

Device switched OFF.

lights

does not

light

Device operating.

PCI slot powered up.

Table 4: Operating system without hot-plug functionality: hot-plug PCI indicator modes

Summary of Contents for PRIMERGY TX300
































































































































Search results

Summary of Contents for PRIMERGY TX300

Reviews:

Fujitsu PRIMERGY TX300, Operating Manual, Page: 69 / 127

Search results

Summary of Contents for PRIMERGY TX300

Reviews: