manualshive.com logo in svg

Fujitsu PRIMERGY TX300 S3, Options Manual, Page: 54 / 109

Share
Download
Fujitsu PRIMERGY TX300 S3 Options Manual Download Page 54

54

Options Guide

 TX300 

S3

Installing a slimline CD/DVD drive

Accessible drives

Figure 42: Inserting CD/DVD drive in the frame

Ê

Connect the data cable to the rear side of the slimline CD/DVD drive (see the 
cabling plans in the Appendix).

Ê

Insert the slimline CD/DVD drive in the frame. The four noses will fasten the 
frame.

Ê

Slide the slimline CD/DVD drive into the mounting location until it latches in 
place. Take care that the data cable does not clamp.

Ê

Connect the power cable to the rear side of the slimline CD/DVD drive (see 
the cabling plans in the Appendix).

I

If a slimline floppy disk drive or a LocalView module has been installed 
above the slimline CD/DVD drive, it is not possible to get access to the 
power connector of the slimline CD/DVD drive. In this case pull out the 
slimline floppy disk drive or the LocalView module as far as you get 
access to the power connector.

Summary of Contents for PRIMERGY TX300 S3














































































































Reviews:

No comments