manualshive.com logo in svg

Fujitsu PRIMERGY TX300 S3, Options Manual, Page: 49 / 109

Share
Download
Fujitsu PRIMERGY TX300 S3 Options Manual Download Page 49

TX300 S3

Options Guide

49

Accessible drives

Installing an accessible 5.25-inch drive

Figure 35: Attaching the EasyClick rails - DVD-ROM burner

Ê

Screw the EasyClick rails onto either side of the new 5.25-inch drive using 
two M3x4.5mm screws (1). 
Use the first hole in each upper row of holes as shown in the figure.

I

Keep the remaining screws for future use. The different drives are 
fastened using different screws. Starting on the next page, you will 
find figures which show the attaching of the EasyClick rails for 
magnetic tape drives.

Ê

Push the new drive about halfway into the bay.

Ê

Connect the data cable to the accessible drive (see the cabling plans in the 
Appendix).

Ê

Connect the power cable to the accessible drive (see the cabling plans in the 
Appendix).

Ê

Push the drive fully into the bay until the EasyClick rails latch in place.

Ê

Attach the front cover or rack front cover, close the server, connect it to the 
power outlet, and switch it on as described in the 

chapter “Completion” on 

page 79

ff.

You will find in the following figures which holes and screws should be used for 
the magnetic tape dives.

1

1

Summary of Contents for PRIMERGY TX300 S3














































































































Reviews:

No comments