Fujitsu PRIMERGY TX300 S3 Options Manual Download Page 26

Page: 26 / 109

Options Guide

TX300

Equipping rules

Main memory

–

The memory modules have to be based on x4 or x8 organised
FBD533/PC2-4200F or FBD667/PC2-5300F fully buffered DIMM modules
and must be populated in pairs. It is only allowed you use memory modules
released by Fujitsu Siemens Computers.

–

Each pair must consist of identical memory modules (2 way interleaved
mode).

–

The module capacity between pairs can differ: pair 1A/1B can be populated
with two 512 Mbyte modules and pair 2A/2B with two 1 Gbyte modules.

The table below shows the order in which the memory banks must be equipped:

Memory mirroring

Either 4 or 8 identical memory modules are required for memory mirroring:

module pair
1A/1B

module pair
1C/1D

module pair
2A/2B

module pair
2C/2D

Equipped

Empty

Equipped

Empty

Equipped

Empty

Equipped

Memory
bank

Channel
(module)

Equipment

4 identical memory modules

8 identical memory modules

Summary of Contents for PRIMERGY TX300 S3














































































































Search results

Summary of Contents for PRIMERGY TX300 S3

Reviews:

Fujitsu PRIMERGY TX300 S3, Options Manual, Page: 26 / 109

Search results

Summary of Contents for PRIMERGY TX300 S3

Reviews: