Fujitsu PRIMERGY TX1330 M4 Operating Manual Download Page 37

Page: 37 / 110

TX1330 M4

Operating Manual

Product description

3.3.3

Indicators on the server rear

3.3.3.1

Indicators on the I/O panel

Global Error, ID and CSS indicators

Figure 11: Global Error, ID and CSS indicators

Pos. Label

Indicator

Status

Description

ID
indicator,
see also

blue on

The server has been highlighted
using ServerView Operations
Manager, iRMC web frontend or
the ID button on the front panel for
easy identification.

flashing
blue

The server has been highlighted
for easy identification using the
iRMC (AVR) with disabled local
VGA output.

[CSS]

CSS
indicator

off

No critical event detected (CSS
component).

orange
on

Prefailure event detected (CSS
component).

flashing
orange

CSS component failure detected.

Summary of Contents for PRIMERGY TX1330 M4















































































































Search results

Summary of Contents for PRIMERGY TX1330 M4

Reviews:

Related manuals for PRIMERGY TX1330 M4

Brands by name

Popular brands

Fujitsu PRIMERGY TX1330 M4, Operating Manual

Search results

Summary of Contents for PRIMERGY TX1330 M4

Reviews:

Related manuals for PRIMERGY TX1330 M4

Brands by name

Popular brands