Fujitsu PRIMERGY TX1330 M4 Operating Manual Download Page 86

Page: 86 / 110

Operating Manual

TX1330 M4

Operation

6.3.1.2

Installing a 2.5-inch HDD/SSD module

Figure 25: Opening the 2.5-inch HDD/SSD module locking lever

Pinch the green locking clip (1) and open the locking lever (2).

Figure 26: Installing the 2.5-inch HDD/SSD module

Insert the HDD/SSD module into a drive bay and carefully push back as far
as it will go (1).

Close the locking lever to lock the HDD/SSD modulein place (2).

When using a RAID array, add the additional HDD/SSD to the RAID array.

Configuring the RAID array, see the documentation of the RAID
controller, used in your configuration, see section

"Documentation

overview" on page 13

Summary of Contents for PRIMERGY TX1330 M4















































































































Search results

Summary of Contents for PRIMERGY TX1330 M4

Reviews:

Related manuals for PRIMERGY TX1330 M4

Brands by name

Popular brands

Fujitsu PRIMERGY TX1330 M4, Operating Manual

Search results

Summary of Contents for PRIMERGY TX1330 M4

Reviews:

Related manuals for PRIMERGY TX1330 M4

Brands by name

Popular brands