Fujitsu PRIMERGY TX1330 M4 Operating Manual Download Page 66

Page: 66 / 110

Operating Manual

TX1330 M4

Starting up

5.4.1

Installing the server in the rack

CAUTION!

At least two people are needed to position the server on the rack rails.
(For Japan, see "

安全上のご注意

".)

Additionally, a lifter is required in the following cases:

– The server weighs more than 50 kg.
– The server weighs more than 21 kg and is to be installed above the

height of 25 U.

When using a lifter, this installation procedure needs to be carried out by
maintenance personnel.

For configurations below 32 kg:

At least two people are needed to lift the server
into the rack cabinet.

For configurations below 55 kg:

At least three people are needed to lift the server
into the rack cabinet.

For configurations above 55 kg:

At least four people are needed to lift the server
into the rack cabinet.

Summary of Contents for PRIMERGY TX1330 M4















































































































Search results

Summary of Contents for PRIMERGY TX1330 M4

Reviews:

Related manuals for PRIMERGY TX1330 M4

Brands by name

Popular brands

Fujitsu PRIMERGY TX1330 M4, Operating Manual

Search results

Summary of Contents for PRIMERGY TX1330 M4

Reviews:

Related manuals for PRIMERGY TX1330 M4

Brands by name

Popular brands